In-Line
Double Reduction Gear Reducers Viking Series:
Size 11 - 100
Gear Ratio Range: 2.60:1
to 35:1
Output Speeds (1750 RPM Input): 673 to 50 RPM
Horsepower Range: .5 to 350 HP
Available Constructions: Aluminum
Sizes 11 through 60 are available in Nema C-Face
Offset
Gear Reducers Viking Series:
A, B, C
Gear Ratio Range: 1.87:1
to 7.95:1
Output Speeds (1750 RPM Input): 950 to 220 RPM
Horsepower Range: 1.4 to 49.8 HP
Available Constructions: Cast Iron
Air
& Gear Motors Gast Mfg.
Used to convert pumps to Pneumatic Drive.
Temperatures to: 250° F
Available Designs: Body Mount, 56C, IEC
Applications: Explosion Proof
Shaft
Couplings Falk Series:
WRAPflex
Falk's unique design allows you to replace the element without moving
the hubs or disturbing the alignment of the equipment.
Coupling Guards Falk Series:
MCG Orange Peel
Easy to use. Just measure & trim to fit. They
are available in three sizes. These guards are made of a sturdy
Polyethylene construction with a stainless steel hinge pin & are
O.S.H.A. approved!
Filter/Regulators Master
Pneumatic
For use with your 'lube-free' air operated diaphragm pump. Controls the speed and extends the life of your diaphragm pump!
Filter/Regulator/Lubricators Master
Pneumatic
For uses with your 'lube-style' air operated diaphragm pump. Controls the speed and extends the life of your diaphragm pump!
Sentry
Pulsation Dampeners
SENTRY®
Pulsation Dampeners / Surge Suppressors remove hydraulic shock and
vibration, enhancing all-around performance and reliability of fluid
flow applications. For sizing, use the SENTRY
SELECTION GUIDE.
Spill-STOP
Leak Containment More than just
leak detection! The patented Spill-STOP® Leak Containment System
prevents costly & hazardous spills caused by pump diaphragm failure
Drum
Unloading Systems All stainless
steel construction
Compatible with all P4 and PV4 metal Original Series pumps.
Integrated control system (all pneumatic).
Two mounting options
Base plate mounted (mobile)
Bolt down configuration (stationary)
Pumps Sold Separately
Relief
Valves Fulflo Series:
V
High quality adjustable hydraulic bypass relief valves to
protect your system.
Pressures: 2 to 1000 PSI
Port Sizes: 3/8" to 2"
Threaded & Flanged
Available Constructions: Cast Iron, Brass, Steel & Stainless Steel
Twin
Shaft Grinders Monoflo
Provide
protection to you pump with high volume, fine grinding of sewage &
sludge.
Flow Rates: 0-3434 GPM
Pressures: To 87 PSI
Mechanical
& Cartridge Seals AESSEAL offers
a variety of standard mechanical & exotic cartridge seals for your
application. Seal kits are available for Flygt, Grindex, Peerless
and many more!
Mechanical
Seals Includes Flush,
Quench and Drain connections for maximum environmental control
capability.
Distributed flush arrangement maximizes cooling effect, prevents
clogging and reduces thermal distortion.
T05 Seal Kits for Flygt
Pumps AESSEAL offers
seal kits for Flygt submersible pumps. Kits include upper/lower
seals, bearings & o-rings. Special tools not required!
Packing Chesterton's
superior packing will reduce leakage & wear, while improving the
life of your equipment.
MagTecta
Bearing Protectors Protect your
bearings with these high quality magnetic double faced bearing
isolators. This is the top of the line bearing protector.
Power
Load Monitors Viking Series:
M10, M20
Motor Protection For Undercurrent & Overcurrent
Horsepowers to: 999 HP
Shuts down pump
from conditions caused by cavitation, dry-run or over-pressure
Pump
Motor Moisture Detectors Warrick Series:
2800/2810
Voltage: 115V/230V/460V/500V/ 575V
Contact Rating: 16 AMP Resistant 1 HP
Connections: Screw Type
Enclosures: Nema 1, Nema 4, Open
Features: Warning Lamp, Test Button
Applications: Submersible Pumps
Pressure
Transducer Kits Goulds Part
#9K391
Includes 25' Cable
Signal: 4-20 mA
Pressure Range: 0-300 PSI
For Use With Goulds Aquavar Controllers
Industrial
Line
Card